一、產品型號規格

Product model specification

●MDA-8000B 10000A標準型Standard 220V 60Hz電源 Source

●MDA-8000A 10000A標準型 Standard 110V 60Hz電源 Source

●MDB-4000B 5000A極性切換型Polarity switching type 220V 60Hz電源

●MDB-4000A 5000A極性切換型Polarity switching type 220V 60Hz電源

二、晶體管焊接電源特點

本公司生產的MDA.MDB系列焊接電源，采用精密型晶體管式焊接電源

Our MDA.MDB series welding power supply adopts precision transistor welding power supply

■ 焊接電源采用晶體管切換方式，能實現小型高效，高輸出的精密焊接

Welding power supply adopts transistor switching mode, which can achieve small, efficient, high output precision welding

■ 本機采用3種焊接方式This machine adopts 3 welding methods：

●定電壓焊接(-----)：控制電極間的電壓，電流量小，降低焊接時產生火花

Fixed voltage welding (-----): control the voltage between the electrodes, low flow rate, reduce the welding of sparks

●定電流焊接(-----)，通過一定量的電流，與工件電阻無關，可穩定焊接

Fixed current welding (-----), through a certain amount of current, independent of the workpiece resistance, can stabilize the welding

●定電壓.定電流焊接(-----)：前部分焊接通過定電壓，后部分定電流焊接

Fixed voltage. Fixed current welding (-----): the front part of the welding through the fixed voltage, the latter part of the fixed current welding

輸出電流方向 Output current direction：

MDA-8000B電流從正極流向負極(單極性方式焊接)，主要適用動力電池類

The MDA-8000B current flows from the positive electrode to the negative electrode (unipolar mode welding), mainly applicable to the power battery class

MDB-4000B(極性轉換方式焊接)，主要適用數碼電池類

MDB-4000B (polar conversion mode welding), mainly suitable for digital batteries

■適合焊接范圍：動力電池/數碼電池/鎳氫鎳鉻電池/電機轉子/電子電氣配件等

Suitable for welding range: power battery / digital battery / MH battery / motor rotor / electronic and electrical accessories, etc

■界面顯示：本機為5寸觸摸顯示屏(DMT80480T050-16WT)，易懂易操作，配自動化機器時可選

Interface display: this machine is a 5-inch touch display screen (DMT80480T050-16WT), easy to understand and easy to operate, optional when equipped with automatic machine

■焊接厚度:0.08-0.2MM鍍鎳或純鎳(0.15-0.2MM鎳片建議開導流槽，0.2MM 以上鎳片需要打凸點焊接)

Welding thickness: 0.08-0.2MM nickel plating or pure nickel (0.15-0.2MM nickel wafer recommended channel, nickel wafer above 0.2MM welding)

■焊接規范存儲：焊接時可以進行更加靈活的選擇規范焊接，輸出不同規范的 焊接參數，列如：正極焊接電流2000A，負極需要2500A焊接電流，在自動焊接機中由自動化給出信號控制輸出相應的焊接規范(對應的焊接電流)，手動操作中需要通過切換控制信號可以實現輸出不同的焊接電流

Welding specification storage: welding can be more flexible selection specification welding, output different specification welding parameters, such as: positive welding current 2000A, negative need 2500A welding current, in automatic welding machine control the output corresponding signal welding specification (welding current), manual operation need to switch control signal can output different welding current

■可設定預熱電流，焊接電流和冷卻，有效地解決了焊接過程中產生的噴濺和焊接結束后工件的淬火問題。二個放電脈沖可單獨或任意組合使用。

The preheating current, welding current and cooling can effectively solve the problems caused during welding and quenching of workpiece after welding.Two discharge pulses can be used individually or in any combination.

■具有電流緩升/緩降功能：使用緩升/緩降功能可以避免焊接時產生噴濺，滿足特殊材料焊接要求。

With the current slow rise / slow drop function: using the slow rise / slow drop function can avoid the splash during welding, and meet the welding requirements of special materials.

■安裝使用方便：體積大大減小，整體設備輕巧，安裝使用方便。

Easy to install and use: the volume is greatly reduced, the overall equipment is light, easy to install and use.

■故障診斷和自動保護功能：機器在工作過程中，控制器如檢測到情況異常，會自動關閉輸出并報警提示。

Fault diagnosis and automatic protection function: during the machine, the controller will automatically close the output and alarm.

■通訊接口：RS485/RS232

Communication Interface: RS485 / RS232

■獨立的外接觸摸顯示屏接口：可選擇外置7寸觸摸顯示屏

(DMT80480T070-18WT)，通訊模式為RS485

Independent external contact touch display interface: optional external 7-inch touch display

(DMT80480T070-18WT), the communication mode is RS485

■點焊數據采集：可通過RS485 或RS232采集焊接數據

Spot welding data acquisition: The welding data can be collected via RS485 or RS232

■外部控制功能：可外接工控機/PLC控制、配合自動化機器生產

External control function: external industrial control machine / PLC control, cooperate with automatic machine production

■外形尺寸：L430MM*W185MM*H400MM

Overall dimensions: L430MM * W185MM * H400MM

■重量Weight：25KG

5.主功能設置 Main function settings

●進入功能區域

Enter the functional area

在任意頁面點擊上方藍色位置都會跳出下拉菜單

Clicking the blue position above any page jumps the drop-down menu

在下拉菜單中選擇需要進入的頁面

Select the page required to enter in the drop-down menu

規范參數設置頁面：

Specification parameter setting page: